Item no.: 6211
DKB502/PRO
Stand-mounted Diamond core drill for wet drilling in concrete, reinforced concrete and masonry
Drilling diameter: 502 mm in the column / hand-held: no
Operation: wet
Mounting: 1 1/4" UNC
Material: concrete, reinforced concrete, stone, masonry
Available between 17.11. and 18.11.
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete | Masonry | Brick | Calcium silicate brick | Facing brick |
| Power consumption: | 3,500 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 250 rpm | 500 rpm | 750 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 14.2 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator | Overload protection | Soft start |
| Max. drilling Ø: | bis 502 mm |
| Product type: | Core drilling rig |
High customer satisfaction
Over 5,000 professionals trust us. We are Trusted Shops certified.
Top-class support
Expert and personalised advice from genuine experts.
Professional quality
Robust equipment for demanding tasks.
German brand
Sales, service and spare parts direct from Germany.
97% satisfaction: Over 5,000 tradespeople and construction companies trust us.
Top-class support: Expert and personalised advice from genuine specialists.
Professional quality: Robust tools for demanding jobs and continuous use.
German brand: Service and spare parts direct from Germany.
DKB502/PRO diamond core drill, stand-mounted only: wet drilling up to 502 mm
The DKB502/pro is ideal for drilling very large openings in a controlled manner using a drill stand: 3,500 watts, three-speed gearbox in an oil bath, wet drilling in concrete, reinforced concrete, stone and masonry up to Ø 502 mm. This is the largest drilling range of our core drilling machines, sufficient for large building penetrations, ventilation ducts and flue pipes.
- Three speeds, 250 / 500 / 750 rpm: low speeds with full torque for large core bits.
- LCD display with performance indicators: current consumption, motor temperature and operating hours at a glance; adjust feed rate according to actual load.
- Soft start, slip clutch, PRCD: smooth start-up, spindle stops in the event of a blockage, personal protection integrated into the cable.
- Supplied in a case with quick-release ring, open-ended spanners and spare carbon brushes: Mounts to the stand via an interface with a key.
Technical Specifications
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete , Masonry , Brick , Calcium silicate brick , Facing brick |
| Power consumption: | 3,500 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 250 rpm , 500 rpm , 750 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 14.2 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator , Overload protection , Soft start |
| Max. drilling Ø: | bis 502 mm |
| Product type: | Core drilling rig |
DKB502/PRO diamond core drill for wet drilling up to 502 mm on a core drill stand
The DKB502/PRO is the stand-mounted wet core drilling rig in the 3.5 kW class: 3,500 watts, three-speed gearbox in an oil bath, for use in a core drill stand up to Ø 502 mm, for concrete, reinforced concrete, stone and masonry. It is not designed for hand-held or dry drilling.
If you purchase the machine and stand together, the DKB502/PRO is available as the DKB502/PRO core drilling system with the KBS502/PRO.
Drilling diameters and materials
The DKB502/pro drills wet in concrete, reinforced concrete and masonry. The water cools the drill bit to prevent it from overheating and wearing out prematurely, and binds the drilling dust into slurry. The unit is designed for use with the stand: it must not be used as a hand-held tool or for dry drilling.
- In a core drill stand: up to Ø 502 mm
- Wet drilling: concrete, reinforced concrete, masonry
- Operating mode: wet only, for use in a core drill stand only
Motor and gearbox
The 3500-watt motor, rated at 230 V and 16 A, operates via a three-speed gearbox in an oil bath. The speeds are lower than on the DKB352/PRO and are therefore suited to large core bits: in first gear they run slowly and at full torque, whilst smaller ones run in third gear at a higher cutting speed. These figures apply to concrete of average hardness; for reinforced concrete, the next lower gear should be selected.
- Gear 1, 250 rpm: up to Ø 502 mm
- Gear 2, 500 rpm: up to Ø 302 mm
- Gear 3, 750 rpm: up to Ø 162 mm
Additional functions
- Soft start: Speed and power increase gradually when the machine is switched on; the drill bit engages without a torque surge, and both the machine and the mains supply are protected during start-up.
- LCD display and performance indicator: Shows voltage, current draw, power consumption, motor temperature and operating hours, plus warning symbols as soon as a safety function is triggered. This allows the feed rate to be adjusted during drilling according to the actual load.
- Carbon brush warning system: Shuts off the machine and displays a message indicating that the brushes need replacing before worn carbon brushes damage the motor. A replacement set is included.
Protective functions
- Slip clutch: Mechanically disengages the power transmission as soon as the drill bit becomes jammed in the borehole; the spindle comes to a standstill.
- Electronic protection: Protected against overload, overvoltage and overheating, with red and yellow warning LEDs.
- Protection class II: Protective insulation; no earth wire required.
- Personal protection switch: PRCD in the mains cable.
On the core drill stand
The DKB502/pro is attached directly to the feed carriage via its interface using four hex socket screws and a key; the fixing materials are supplied with the core drill stand. Water is supplied via the Gardena connection with a ball valve; for drilling vertically upwards, a water collection ring is included to prevent water from running onto the machine. The machine has a carrying handle for transport. If a core bit becomes stuck after drilling, the enclosed quick-release ring and the two open-ended spanners can be used to loosen it without damaging the thread.
- Weight: 14.2 kg
- Tool holder: 1 1/4" UNC external
- Water connection: Gardena coupling with ball valve, up to 3 bar
Compatible core drill stands and core bits
Which of our core drill stands is suitable depends on the diameter and drilling depth. All three are fixed with wall plugs and have a mobile base:
- KBS502/PRO: Up to Ø 502 mm and 650 mm drilling depth, with 0 to 45-degree tilt for angled drilling. Covers the full drilling range of the DKB502/PRO and is the first choice.
- KBS352/PRO: Up to Ø 402 mm and a drilling depth of 650 mm. Limits the drilling range to 402 mm.
- KBS352/XL-PRO: Up to Ø 352 mm, with a 2 m long guide stand for drilling depths of up to 1600 mm. For thick walls and foundations, up to 352 mm.
Our compatible 1 1/4" UNC diamond core drill bits: wet diamond core bits for concrete and reinforced concrete.
Contents
The DKB502/pro comes in a sturdy storage case with everything you need for your first use:
- Quick-release ring for diamond core drill bits
- Open-ended spanners (SW32 and SW41)
- Set of spare carbon brushes
- Earplugs and safety goggles
- Operating instructions
Core drill stands and diamond core drill bits are not included.
Dimensions 610 x 195 x 135 mm, weight 14.2 kg, case dimensions 630 x 440 x 200 mm.
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete | Masonry | Brick | Calcium silicate brick | Facing brick |
| Power consumption: | 3,500 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 250 rpm | 500 rpm | 750 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 14.2 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator | Overload protection | Soft start |
| Max. drilling Ø: | bis 502 mm |
| Product type: | Core drilling rig |
Get in touch with us
Do you have any questions or would you like some professional advice? You can contact us in person, by telephone, by email or via WhatsApp.
Get in touch now