Item no.: 6206
DKB352/PRO
Stand-mounted Diamond core drill for wet drilling in concrete, reinforced concrete and masonry
Drilling diameter: 402 mm in the stand / not suitable for freehand use
Operation: wet
Shank: 1 1/4" UNC
Material: concrete, reinforced concrete, stone, masonry
Available between 17.11. and 18.11.
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete | Masonry | Brick | Calcium silicate brick | Facing brick |
| Power consumption: | 3,300 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 700 rpm | 350 rpm | 1,100 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 13.5 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 | 6216 | 6299 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator | Overload protection | Soft start |
| Max. drilling Ø: | up to 500 mm |
| Product type: | Core drilling rig |
High customer satisfaction
Over 5,000 professionals trust us. We are Trusted Shops certified.
Top-class support
Expert and personalised advice from genuine experts.
Professional quality
Robust equipment for demanding tasks.
German brand
Sales, service and spare parts direct from Germany.
97% satisfaction: Over 5,000 tradespeople and construction companies trust us.
Top-class support: Expert and personalised advice from genuine specialists.
Professional quality: Robust tools for demanding jobs and continuous use.
German brand: Service and spare parts direct from Germany.
DKB352/PRO diamond core drill, stand-mounted only: wet drilling up to 402 mm
The DKB352/PRO is ideally suited to large core drilling operations carried out cleanly and precisely whilst mounted on a stand: 3,300 watts, three-speed gearbox in an oil bath, wet drilling in concrete, reinforced concrete, stone and masonry. Building service penetrations, supply lines, ventilation and flue pipes – where hand-held machines are no longer sufficient.
- Up to Ø 402 mm in a core drill stand: three speeds at 350 / 700 / 1100 rpm; each diameter runs at the appropriate speed.
- LCD display with performance indicators: current consumption, motor temperature and operating hours at a glance; feed rate adjusted according to actual load.
- Soft start, slip clutch, PRCD: smooth start-up; spindle stops in the event of a blockage; personal protection integrated into the cable.
- Supplied in a case with quick-release ring, open-ended spanners and spare carbon brushes: Mounted on the stand via an interface with a key.
Technical Specifications
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete , Masonry , Brick , Calcium silicate brick , Facing brick |
| Power consumption: | 3,300 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 700 rpm , 350 rpm , 1,100 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 13.5 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 , 6216 , 6299 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator , Overload protection , Soft start |
| Max. drilling Ø: | up to 500 mm |
| Product type: | Core drilling rig |
DKB352/PRO diamond core drill for wet drilling up to 402 mm in a core drill stand
The DKB352/PRO is the 3-kW class stand-mounted wet core drilling rig: 3, 300 watts, three-speed gearbox in an oil bath, for drilling up to Ø 402 mm in a core drill stand, suitable for concrete, reinforced concrete, stone and masonry. It is not designed for hand-held or dry use.
If you purchase the machine and stand together, the DKB352/PRO is available as the DKB352/PRO core drilling system with the KBS352/PRO or as the DKB352/PRO core drilling system with the KBS352/XL-PRO for drilling depths up to 1600 mm.
Drilling diameters and materials
The DKB352/PRO drills wet in concrete, reinforced concrete and masonry. The water cools the drill bit to prevent it from overheating and wearing out prematurely, and binds the drilling dust into slurry. The machine is designed for use with the stand: it must not be used hand-held or for dry drilling.
- In a core drill stand: up to Ø 402 mm
- Wet drilling: concrete, reinforced concrete, masonry
- Operating mode: wet only, for use in a core drill stand only
Motor and gearbox
The 3300-watt motor, rated at 230 V and 16 A, operates via a three-speed gearbox in an oil bath. Each gear has its own diameter range: large core bits run slowly in first gear with full torque, whilst small ones run in third gear at high cutting speed. These figures apply to concrete of average hardness; for reinforced concrete, the next lower gear should be selected.
- Gear 1, 350 rpm: up to Ø 402 mm
- Gear 2, 700 rpm: up to Ø 202 mm
- Gear 3, 1,100 rpm: up to Ø 102 mm
Additional functions
- Soft start: Speed and power increase gradually when switched on; the drill bit engages without a torque surge, and the machine and mains supply are protected during start-up.
- LCD display and performance indicator: Shows voltage, current draw, power consumption, motor temperature and operating hours, plus warning symbols as soon as a safety function is triggered. This allows the feed rate to be adjusted during drilling according to the actual load.
- Carbon brush warning system: Shuts off the machine and displays a message indicating that the brushes need replacing before worn carbon brushes damage the motor. A replacement set is included.
Protective functions
- Slip clutch: Mechanically disengages the power transmission as soon as the drill bit becomes jammed in the hole; the spindle comes to a standstill.
- Electronic protection: Protected against overload, overvoltage and overheating, with red and yellow warning LEDs.
- Protection class II: Protective insulation; no earth wire required.
- Personal protection switch: PRCD in the mains cable.
On the core drill stand
The DKB352/PRO is attached directly to the feed carriage via its interface using four hex socket screws and a key; the fixing materials are supplied with the core drill stand. Water is supplied via the Gardena connection with a ball valve; for drilling vertically upwards, a water collection ring is included to prevent water from running onto the machine. The machine has a carrying handle for transport. If a core bit becomes stuck after drilling, the enclosed quick-release ring and the two open-ended spanners can be used to loosen it without damaging the thread.
- Weight: 13.5 kg
- Tool holder: 1 1/4" UNC external
- Water connection: Gardena coupling with ball valve, up to 3 bar
Compatible core drill stands and drill bits
Which of our core drill stands is suitable depends on the diameter and drilling depth. All three are fixed with dowels and have a base:
- KBS352/PRO: Up to Ø 402 mm and a drilling depth of 650 mm. Covers the full drilling range of the DKB352/PRO and is the first choice.
- KBS352/XL-PRO: Up to Ø 352 mm, with a 2 m-long guide stand for drilling depths of up to 1600 mm. For thick walls and foundations.
- KBS502/PRO: Up to Ø 502 mm and a drilling depth of 650 mm. The ideal choice when larger machines are also in operation on the same stand.
Our matching diamond core drill bits with 1 1/4" UNC: wet diamond core bits for concrete and reinforced concrete.
Contents
The DKB352/PRO comes in a sturdy storage case with everything needed for initial use:
- Quick-release ring for diamond core drill bits
- Open-ended spanners (SW32 and SW41)
- Set of spare carbon brushes
- Earplugs and safety goggles
- Operating instructions
Core drill stands and diamond core drill bits are not included.
Dimensions 610 x 195 x 135 mm, weight 13.5 kg, case dimensions 630 x 440 x 200 mm.
| Product type: | Diamond core drill |
|---|---|
| Suitable for: | Reinforced concrete | Masonry | Brick | Calcium silicate brick | Facing brick |
| Power consumption: | 3,300 W |
| Voltage / Frequency: | 230 V / 50 Hz |
| Protection class: | I |
| Number of gears: | 3 |
| Idling speed: | 700 rpm | 350 rpm | 1,100 rpm |
| Gearbox lubrication: | Oil bath |
| Tool holder: | 1 1/4" UNC |
| Water supply connection: | Gardena |
| Weight: | 13.5 kg |
| Vibration level: | 6 m/s² |
| Suitable for: | 6215 | 6216 | 6299 |
| Wet/dry drilling: | Wet |
| Drill guide: | Guide-railed |
| Additional functions: | LED/Load Indicator | Overload protection | Soft start |
| Max. drilling Ø: | up to 500 mm |
| Product type: | Core drilling rig |
Get in touch with us
Do you have any questions or would you like some professional advice? You can contact us in person, by telephone, by email or via WhatsApp.
Get in touch now